氣動剪板機的全技術措施呢主要有以下10點：
第一點呢是當剪板機的間隙小于等于6mm的時候呢，就不需要安裝安全防護裝置了。
第二點呢是剪板機應該有單次循環的模式，選擇單次循環模式后，即使控制裝置持續有效，那刀架和壓料裝置也只能工作一個行程，第3點呢是壓料裝置應確保剪切鉗將剪切材料壓緊，壓緊后呢板料在剪切時不能移動，
第4點安裝在刀架上的刀片呢應該固定可靠，不能僅靠摩擦安裝固定，
第5點剪板機上的所有緊固件應緊固，并應采取防松脫的措施，以免引起傷害，
第6點呢是在使用剪板機的時候，剪板機后部落料危險區一般的應該設置阻擋裝置，以防止人員發生危險，
第7點應根據剪板機自身的結構性能特點設置格式的安全監督控制裝置，對機器的安全運行狀況進行監控，
第8點剪板機上呢必須設置緊急停止按鈕，一般呢應在剪板機的前面和后面分別進行設置，
第9點如果剪板機配有激光器來指示剪切線，應符合安全標準的相關規定，以確保不是對人身造成傷害，
第10點復位裝置呢應該放置在可以清楚觀察危險區域的位置，每一個檢測區域嚴禁安裝多個復位裝置，如果后面由光電保護裝置進行防護，每個檢測區域呢應安裝一個復位裝置。
以上呢就是剪板機的相關安全技術要求了。
The full technical measures for pneumatic shearing machines mainly include the following 10 points:
The first point is that when the gap between the shearing machine is less than or equal to 6mm, there is no need to install safety protection devices.
The second point is that the shearing machine should have a single cycle mode. After selecting the single cycle mode, even if the control device is continuously effective, the knife holder and the pressing device can only work for one stroke. The third point is that the pressing device should ensure that the shearing pliers press the shearing material tightly, and after pressing, the sheet material cannot move during shearing,
The blade installed on the tool holder should be securely fixed and not solely fixed by friction,
All fasteners on the shearing machine should be tightened and anti loosening measures should be taken to avoid injury,
The sixth point is that when using a shearing machine, a blocking device should generally be installed in the danger zone of material falling behind the shearing machine to prevent personnel from being in danger,
Point 7: Safety supervision and control devices should be set up according to the structural performance characteristics of the shearing machine itself to monitor the safe operation of the machine,
The eighth point is that an emergency stop button must be installed on the shearing machine, which should generally be set separately in front and behind the shearing machine,
If the shearing machine is equipped with a laser to indicate the cutting line, it should comply with relevant safety standards to ensure that it does not cause harm to personnel,
The reset device should be placed in a position where the danger area can be clearly observed. It is strictly prohibited to install multiple reset devices in each detection area. If it is protected by a photoelectric protection device later, a reset device should be installed in each detection area.
The above are the relevant safety technical requirements for the shearing machine.
|
